Field notesPainting

Exterior Painting on High-Rise Buildings: Coatings, Cycles and the Cost of Cutting Corners

A repaint is not really a paint job. It is a protective coating system that holds the building envelope together. Here is what owners corporations should know about specification, preparation and warranty before approving the next cycle.

24 October 2025 · 6 min read

A repaint on a tower is not really a paint job. It is the renewal of the protective coating system that keeps the building envelope watertight, UV-stable and visually intact for the next decade. Treating it as decoration is the single most expensive mistake an owners corporation can make, because the difference between a properly specified coating system and a budget repaint shows up not in year one. When both look fine. But in year four, when one is still performing and the other is bubbling, chalking and pulling moisture into the wall behind it.

This article explains, in plain language, what a high-rise coating system actually is, what good preparation looks like, how to read a warranty, and where the temptation to cut corners costs the most.

What a coating system actually is

A modern exterior coating is not one product. It is a system, usually three coats, each engineered to do a specific job.

The first coat is a primer or sealer. Its role is to bind to the substrate. Concrete, render, fibre cement, previously painted surface. And to give the following coats a stable surface to adhere to. On a previously coated facade the primer is often a penetrating sealer designed to lock down chalky residue from the old coating. On bare or repaired concrete it is a high-build primer designed to even out the surface profile.

The second and third coats are the build coats and the topcoat. On high-rise work these are almost always elastomeric or 100 per cent acrylic membranes specified for exposure category. Their job is to form a continuous film with enough flexibility to span hairline cracks in the substrate, enough UV stability to hold colour for a decade, and enough breathability to let trapped moisture escape without blowing the coating off the wall.

Used as a system, those three coats deliver a service life of ten to fifteen years on a properly prepared substrate. Used separately, or with one product substituted out for a cheaper alternative, the system warranty disappears and the actual life can drop to four or five years.

Preparation is most of the job

The cliché in the trade is that paint is twenty per cent product and eighty per cent preparation. On high-rise work that ratio is, if anything, generous to the paint.

A proper prep sequence on a tower starts with pressure washing every elevation to remove salt, pollution, biological growth and loose coating. On a coastal building the wash also flushes chloride contamination off the surface before it can interfere with adhesion. Pressure is calibrated to the substrate. Too much and you damage render and sealants; too little and you leave a contaminant film that the new coating will eventually let go of.

Once the building is washed and dry, every defect on the wall is repaired. Cracks are routed and filled with a flexible filler matched to the coating. Spalled concrete is treated as a concrete repair, not patched with filler. Failed sealant joints. Particularly at window heads, expansion joints and balcony interfaces. Are cut out and replaced with new sealant of the correct grade. This is where a good repaint quietly does most of its long-term work: it locks the building back up before sealing it under a new coating.

Glossy or chalky areas are sanded or chemically prepared so the new primer has something to bond to. Bare metal. Handrails, brackets, fixings. Is treated with a rust-converting primer before the topcoat goes on. Anywhere the old coating is sound it is left in place; anywhere it is failing it is removed back to a stable edge.

Only when all of this is done does any colour go on the wall. A contractor who is on the rope painting in week one of a six-week project is not preparing properly, and the price they quoted reflects that.

Reading a warranty honestly

Coating warranties are a useful sales tool and a confusing piece of paperwork. The headline number , "ten year warranty", "fifteen year warranty". Is almost meaningless on its own. What matters is what the warranty actually covers, who issues it, and what conditions void it.

A real coating warranty is issued jointly by the paint manufacturer and the applicator. The manufacturer warrants the product against premature film failure when applied to specification. The applicator warrants the workmanship. That the prep was done properly and that the product was applied at the specified film build. Both parties have to be involved, because either one alone can compromise the result.

The warranty will list specific failure modes that are covered (typically loss of adhesion, premature chalking, colour fade beyond a defined tolerance) and specific exclusions (mechanical damage, substrate movement beyond the coating's capability, failure to maintain the surface). It will also usually require periodic washdowns and a documented inspection at the midpoint of the warranty period. None of this is unreasonable, but it does mean the warranty is a maintenance contract, not an insurance policy. A building that ignores the maintenance schedule and then tries to claim is unlikely to succeed.

Ask for the warranty terms in writing before you accept the quote, not after the work is done. If the warranty is issued by the applicator alone, with no manufacturer involvement, it is worth roughly as much as the applicator's ongoing business. Which is to say, not much, in an industry with the turnover this one has.

Where corner-cutting hides

There are three places where cheaper quotes usually save their money, and all three show up later as defects.

The first is prep. Fewer hours of washing, less crack repair, no sealant replacement, no spot priming. The wall looks the same on handover and starts failing in year three.

The second is film build. The specified system might call for three coats at a defined dry-film thickness per coat. A budget repaint quietly drops to two coats, or applies three coats thinner than specified. The coverage looks complete because the colour change hides it, but the film is too thin to perform its UV and waterproofing role for the warranted life.

The third is substitution. The quote names a premium coating system, but a cheaper product from a different manufacturer is actually applied. There is no obvious way to detect this from the ground, and the only protection is to require batch numbers and delivery dockets to be supplied for every product used, matched to the elevation it was applied to.

What a properly run project looks like

A well-run exterior repaint on a strata tower runs to a written specification, prepared by either the manufacturer's technical representative or an independent consultant. The specification names the products, the film build, the prep standard and the inspection holds. The applicator works to that specification, the manufacturer's representative inspects at agreed points, and the building manager receives a coating dossier on completion that records what was used where.

That sounds like overhead, and on a single-storey building it would be. On a high-rise repaint costing six or seven figures, with another six or seven figures of potential remediation hidden behind a failed coating, it is the cheapest insurance the building will buy that decade.

Talk to the team

Need a real set of eyes on your building?

We provide facade inspections, coating specifications and remediation scopes across South East Queensland and Northern NSW.

Request a FREE quote